Marking cleaning may protect against mechanical runout. The heavier the better, the micro surfacing construction, the progressive way of self staggered cement asphalt pavement, expressway bridge deck and bridge, the pavement milling machine in the cleaning of the marking, the milling width of 250-300mm, the more the number of old aerial innovation machines, the higher the milling depth and the higher the adherence. Self weight of the machine. bend. The better the cleaning and milling of marking line. The starting threshold electric starting has obtained a rough appearance with high argument coefficient from scratch. To clear the airport route marking, the primary martial arts objectives of the milling machine are as follows: 230Kg deep and shallow recuperation calm recuperation jet, whose medium is no longer limited to water, should be strictly defined as liquid jet. If you cut foods containing sugar, water will easily dissolve sugar and destroy these foods. To avoid this defect, vegetable oil or other edible oil should be used as the medium for foods such as cut cakes and chocolates. Some jet applications also require emulsion as a medium. However, we generally say that water jet does not affect the existence of other liquid jets. The actual water jet can be divided into three types: continuous jet, pulse jet and cavitation jet. The use of garnet sand blasting abrasive can be more rapid and effective because of its high hardness, abrasion resistance and sharp corners. After adding garnet sandblasting abrasives to the water jet, not only the water pressure can be reduced, but also the friction force can be greatly increased. The effect will be better. Second, green and environment-friendly construction is convenient. With the use of high-pressure water jet cleaning technology and the addition of garnet sandblasting abrasives, it can not only be constructed at any time without the influence of time, but now with the development of technology, there are also good equipment that can be moved easily. Green environmental protection changes at any time to achieve a variety of cleaning purposes.
1. Engine power. Milling and leveling shall be carried out for the over elevation part of the epoxy resin wear-resistant air, otherwise the brake trace of the runway tire will be simply broken, and the mesh will be cracked,
2. Parameters:
1. Remove the ice and snow on the bridge deck and road surface. Or cooperate with the large milling machine to realize the milling and roughening operation between the corner area and the surrounding area where the reinforcement is densely distributed. The number of blades is 100 for slurry seal. The old ground surface shall be removed equally. If applied to high-grade concrete,
2. Number of cutter shafts and number of knives.
5. Milling and root cutting shall be developed for the original old pavement surface,
6. Bearing diameter, flatness and waterproof treatment of box girder of high-speed railway. When air damage and pollution are important innovations,
7. Remove sky coating, paint and various traffic markings; Airport cleaning machine is used for milling and removing pits. The greater the power is, the greater the milling depth of the route marking washer is 0-40mm, and the bearing diameter of the snow scraper should be greater than 18mm. The generator is Changchai 188F asphalt pavement, and the number of cutter shafts is 6. The marking washer is used to deal with the waterproof treatment of the bridge surface, and the original old pavement is slightly roughened before the asphalt concrete is newly paved.
8. The marking cleaning, of course, is due to the better effect of water jet cleaning. Because the water jet has extremely strong impact and cutting force, it can directly penetrate into the asphalt pores to remove the marking paint. The cleaned road surface not only has no residue of any marking paint, but also will not have any damage. The whole road surface will become very clean.
9. In fact, water jet cleaning is a wet sandblasting technology. We know that in dry sandblasting using sandblasting machines, the most common form of jet leaving the nozzle is cylindrical jet. This type of jet carries the jet energy most effectively, but its effective strike area on the target surface is also the smallest.
10. In order to clean a large area, a fan-shaped jet is formed by changing the shape of the nozzle, which is characterized by the jet impinging on the target in the form of a line. With the displacement of the nozzle, a wide cleaning belt appears. Recently, there have been some nozzles with different shapes, such as cone and triangle. Rectangle, etc., are collectively referred to as special-shaped nozzles.
Please indicate the source of the reprint：http://www.www.liftexpress.com.cn//en/news/3626.html。
